Katalog » ECU/CHIP-Tuning
Wybierz kategorię
- EEPROM
- ETSmart
- NDM457C
- NEC
- ST7282
- ST92F120
- TMS
Numer kontaktowy

516-301-302

poniedziałek - piątek
w godzinach 10-18

Koszyk
Twój koszyk jest pusty
Wyszukiwarka


Zaawansowane wyszukiwanie
Uwaga !

NIE SERWISUJEMY CHIŃSKICH PRODUKTÓW !

Dla zarejestrowanych klientów i odbiorców hurtowych rabaty !


Grupy dyskusyjne - mailingowe

autoelektronika
liczniki
airbag
radiocode

Payment methods:







Podgląd zamówienia

Aby sprawdzić status zamówienia Wpisz jego unikalny numer
Ciekawe strony


http://www.auto-zamki.pl

http://wiki.ross-tech.com


Waluta
Shipping:

Priority: 3 - 14 days
starts at: 6 EUR


2 - 4 days
starts at: 40 EUR

Język
English
Statystyki
Gości online: 0
Online
Informacje o produkcie
PowerBox dla PCMFlash z kablami

The tool is designed for connecting an ECU to a J2534 device and provides manual or automatic control of the unit power and shaping of the following signals: RESET, BOOT, CNF1, GPT1, GPT2, WATCDOG.

It is required for the Tricore BSL module for PCM Flash

It is compatible in the automatic mode with the loading programs which use:
•    BOOT-OEM12, 12 pin OBD-II;
•    L-LINE, 15 pin OBD-II.

The tool has built-in current limiting resistors on the following signal lines:
•    RESET — 510 Ω;
•    BOOT — 510 Ω;
•    CNF1 — 220 Ω.

The tool is fitted with multipurpose connectors which allow to establish the connections flexibly:

•    USB, designed for connecting to the computer. It is to be connected when the built-in USB — UART converter is enabled; for PowerBox software update; while reprogramming Renesas CPUs;
•    DC, designed for powering the built-in circuit as well as the connected ECU. It is recommended to use only quality units with 12V output voltage. While reading the password, when it is impossible in the vehicle, one must note that high-voltage converters in ECUs consume rather high current at the start which can trigger protection mechanism or even result in the power unit damage;
•    J2534 (OBD-II-F), designed for connecting the same name interface to OBD-II;
•    DB-15, designed for connecting to the main ECU connector. It is recommended to use  14P600KT02, 14P600KT03 cables or analogous ones;
•    IDC-26, designed for connecting directly to the ECU board or via the adapter to the special head. It is recommended to use 14P600KT06 cable or an analogous one for Tricore GPT.
It is recommended to use Flash Development Toolkit software for flashing Renesas CPUs.

Controls:

The tool has 3 switches for operating in different   modes.
•    «POWER», power control. The tool has three modes of power supply to the ECU: OFF allows to remove all power and control signals from IDC-26 and DB-15 connectors; MANUAL supplies power to VECU and VKEY terminals and to the control outputs depending on the chosen tactics; AUTO, automatic control, in this mode power is controlled by the loading program with L-Line signal (15 pin OBD-II).
•    «BOOT», simultaneous control of BOOT, RESET and CNF1 signals (3.3V): OFF, allows to remove all control signals from DB-15 connector; MANUAL pulls RESET and BOOT to the signal minus, and CNF1 to +3.3V; AUTO, automatic control,  in this mode BOOT, RESET and CNF1 signals are simultaneously controlled by the loading program (12 pin OBD-II, OEM12).
•    «GPT», for Renesas and Tricore with GPT CPUs. It is necessary to use 5V while working with SH705x CPUs, in other cases 3.3V is to be used.

Lights:

•    LED near the 5V/3.3V switch indicates 5V or 3.3V voltage supply.
•    VECU, VKEY LED indicates VECU and VKEY voltage supply.
•    12V LED indicates power voltage.
•    BOOT LED indicates voltage on CNF1 output (the LED works both for input and output).

Package contains:

PowerBox for PCMFlash
Bosch EDC17-MED17 GPT cable
Main cable

 

Cena
Ilość
590,40 zł z VAT
480,00 zł netto
Galeria
Inni klienci kupujący ten produkt zakupili również

Professional multi-diagnostic & SAE J2534/RP1210 programming device
interfejs oryginalny
współpracuje z PCMFlash
obsługuje także moduł 29 Ford z transmisją PWM i inne K+CAN
Aktywne moduły: 45, 48, 50, 53, 57, 58, 65, 66, 69, 70, 71
brak możliwości dokupienia dodatkowych modułów i aktualizacji
współpracuje z dowolnym interfejsem J2534:
OpenPort 2.0, Chipsoft J2534, Dialink, Mongoose,
Teradyne GNA600 (VCM 1), Mazda VCM 2, Scanmatik 2 / 2 PRO
K-TAG / NEW TRASDATA
Alientech: 144300T108
Dimsport: F34NTA14

MEDC17 Tricore Bootloader Bench Read/Write (Flash + EEprom)
Tricore Boot/OBD mode, Delphi DCM3.7
Aktywne moduły: 50, 53, 54, 65, 71
brak możliwości dokupienia dodatkowych modułów i aktualizacji
współpracuje z dowolnym interfejsem J2534:
OpenPort 2.0, Chipsoft J2534, Dialink, Mongoose,
Teradyne GNA600 (VCM 1), Mazda VCM 2, Scanmatik 2 / 2 PRO
do interfejsu Scanmatik 2 / 2 PRO
kabel z elektroniką, 3 LED
oznaczniki na przewodach

Negocjacja ceny
dla ilości większej niż 1 szt.
Imię i nazwisko:
E-mail:
Twoja propozycja cenowa lub pytanie:
Wpisz kod widoczny na obrazku:
weryfikator
5747474
Data Ostatniej Aktualizacji: 08.08.2022
© Sklep@AutoDiag.pl. Wszelkie Prawa Zastrzeżone. All Rights Reserved.